Hainan Xinrui Furniture Co., Ltd.

Home  ›  Services

Six stations, one long bench

Every service below happens in the working bays of Hainan Xinrui Furniture Co., Ltd. at Site A5 Phase 1 Dadongyang Furniture City, No. 131 Yehai Avenue, Fengxiang Subdistrict, Qiongshan District, Haikou - 570000, China (CN). Read the detail, then call +19124543953 to pick a station.

The shop is organised as one continuous flow rather than a set of separate trades. A chair arrives at the intake desk, passes a frame inspection, moves to the weaving bench, is sealed on an oil day and returns to its owner with a care note. No stage is skipped and no seat leaves the bench before the frame behind it has been checked. That order is the reason our repairs hold up in humid coastal air. The six services below map directly onto that flow, so you can see exactly where a piece will spend its time.

  • Cane Bay Desk

    The cane bay desk is the front door of the workshop. When a chair arrives we set it on the intake trestle, photograph it from four angles and record the seat dimensions, the frame timber and the condition of the cane that remains. The desk has a small library of cane grades, from fine machine cane to wide hand-rattan strips, and the weaver explains which grade suits the frame and why. Owners who are unsure whether a piece is worth repairing get an honest read on the spot.

    Booking is handled here too. Once a repair is agreed we write a bench ticket with the expected window and the finish option, then explain how to care for the seat after handover. Walk-in questions, spare parts and care advice all run through this desk, which is why it sits closest to the showroom floor where visitors first arrive.

  • Caning Row Rounds

    The caning row rounds are the heart of the trade. Cane is soaked until it flexes without cracking, then laid around the seat frame in even passes, first across the grain and then along it. Each round is tensioned by hand and checked before the next one starts, so a fault is caught while the strand can still be adjusted rather than after the seat is closed.

    A round is quiet, repetitive work with a clear rhythm. Weavers read the sound of the cane as it tightens and watch the way light moves across the surface. A good seat has a slight give under the hand and a clean line where the strand enters the frame. Most dining chairs need several rounds across one working day, and each round is logged so the owner can see what was done.

  • Weave Weeks

    Some pieces deserve longer than a single bench day. Bench backs, decorative seat medallions, woven panels and heirloom chairs are scheduled into weave weeks so they get uninterrupted attention and the steadier humidity that a longer stay in the bay provides. During a weave week the workshop keeps one bench reserved for pattern work and rotates the general repairs around it.

    Because a weave week is planned in advance, owners know when their piece will reach the bench and roughly when it will be back in their hands. Pattern choices are settled at the cane bay desk so the weaver can lay out the geometry before the first strand is soaked. Restoration work with historically accurate patterns also runs best inside a weave week, when reference notes can sit beside the bench for the whole run.

  • Oil Finish Days

    Oil finish days close a batch. Freshly woven cane is brushed clean, then rubbed with a plant-based oil blend in two or three thin coats. Between coats the seat rests, and the final pass is a buffing rub that evens the amber tone across the weave. The finish is the difference between cane that drinks moisture from the air and cane that holds a steady sheen through the wet season.

    We schedule finish days in batches so that the drying racks fill together and settle at the same rate. Owners receive a short care note at handover, covering wiping, humidity and the rare refresh coat. We do not apply a hard lacquer over the oil, because a flexible seat needs a finish that moves with it rather than one that cracks along the frame edge.

  • Frame Check Sessions

    A frame check happens twice, once before the weave and once before handover. We test every joint by hand, look for dry rot at the seat rail, check the front stretcher for movement and listen for the creak that signals a loosening glue line. If a joint needs regluing it is done before any cane is laid, because a new seat on a failing frame will only transfer stress back into the timber.

    The session is also where we advise on reinforcement. A small corner block or a hidden brace can extend the life of a tired chair by years without changing its look. If a frame is beyond saving we say so, explain the reason and suggest alternatives rather than take on a repair that would not last.

  • Showroom Evenings

    Showroom evenings are open sessions where the bench becomes a small stage. A weaver demonstrates a full pass, from soaking the cane to setting the first row, and guests are invited to handle the tools and feel how tension changes along a strand. The sessions are free, informal and limited in number so that everyone can stand close enough to see the weave.

    These evenings are also the best time to ask about a family chair before committing to a repair. Bring the piece, or bring photographs, and we can talk through options while the bench is still warm. Session dates are confirmed through the shop line, and questions go to furniture@xinruifurniture.lol at any time.

How a piece moves through the shop

The process overview below is the same order for every repair, whether it is a single dining chair or a matched set of six.

  1. Intake at the desk. The chair is measured, photographed and given a bench ticket with a grade and finish choice.
  2. Frame check before weave. Joints, rails and stretchers are tested and any regluing is done first.
  3. Caning rounds. Cane is soaked and laid in checked passes, or held for a weave week when the pattern demands it.
  4. Oil finish. Thin coats are rubbed in, rested and buffed until the tone is even across the seat.
  5. Second frame check and handover. The finished piece is reviewed, cleaned and returned with a care note.
  6. Aftercare. Owners can bring a piece back for advice, a refresh coat or a second seat at any time.

Ready to put a chair on the bench?

Call the shop, send a photograph, or simply walk in during showroom hours. We will tell you plainly what the piece needs.

Contact the Haikou showroom →